焊丝中Si元素含量对铝合金接头裂纹敏感性的影响规律及机理

使用扫描电镜、能谱、温度场实时采集等测试方法，研究了焊丝中Si含量对AA6063铝合金GMAW焊接头热裂纹敏感性的影响规律及机理. 结果表明，当焊丝为纯铝时，鱼骨试样的焊缝中心会出现细长的焊接裂纹；当焊丝中的Si含量为4.5% ~ 6%时，裂纹的长度变短，但是开裂距离明显增加；当焊丝中的Si含量达到11% ~ 13%时，试样焊缝无裂纹出现. 随着Si含量的不断提高，合金易出现裂纹的凝固温度区间先增大后减小；焊丝中Si含量的不同还会影响凝固后期金属液的流动性，使得焊缝晶界处的物相成分和形态都有明显的区别；同时，Si含量的提高会使得接头的冷却速度先增加后减小，从而导致应力状态改变，热裂纹敏感性先升高后降低.     

氮对镀锡钢板的强化作用

通过物理化学相分析研究了3种不同氮含量镀锡板中固溶氮、化合氮的含量,结合相关理论计算了镀锡板中氮的固溶强化和析出强化对强度的贡献。结果表明:随着总氮含量从0.0021%提高到0.0103%,钢中化合氮含量下降10.1%,但是AlN析出相中的氮的含量上升10.7%。氮在提高镀锡板强度方面发挥重要作用,钢中总氮含量提高0.0082%,其对屈服强度的贡献值提升约30 MPa。     

规整有机分子自聚集体对铜的高效缓蚀的研究

通过多步法合成了离子型含双苯并三氮唑环的目标分子，4，4'-{苯-1，3-二基二[(1E)-3-羰基丙-1-烯-1，3-二基]}二[2-(2H-苯并三唑-2-基)苯醇酸]二钾。在室温条件下，目标分子在3.5%（质量）NaCl/DMSO（二甲基亚枫）混合溶液 （体积比：40/60） 中能够发生分子自组装产生纳-微米级的自聚集体。通过傅里叶变换红外光谱 （FT-IR）、拉曼光谱和X射线光电子能谱 （XPS） 的表征，证实了所形成的目标分子自聚集体能够对铜表面产生强烈的化学吸附作用，在铜表面形成自组装膜。利用电化学方法测定了目标分子自聚集体吸附在铜表面形成自组装膜后，在3.5%（质量）NaCl溶液中的缓蚀性能。结果表明目标分子自聚集体在NaCl溶液中能高效地抑制铜腐蚀。     

An efficient method of generating vortex electromagnetic wave based on double‐layer transmissive metasurface

A broadband double‐layer transmissive metasurface (TMS) for effective generate vortex electromagnetic wave is presented in this paper. The proposed TMS consists of two types of elements. The first element is composed of a multi‐resonant dipole and four metal vias. The metal vias increase the coupling strength between the upper and lower layers to improve transmission efficiency. On the basis of the first element, the second element adds stubs to ensure sufficient phase shift. The far‐field cross polarisation is eliminated by special element arrangement. Then, a centre‐fed linear polarisation TMS is designed to generate orbital angular momentum beams with mode l = ? 1. The proposed TMS is designed, manufactured and measured to verify the proposed design. The measured results indicate that a maximum gain of 20.8 dBi and narrow divergence angle of ±5° are achieved at 18 GHz. Furthermore, mode purity is higher than 86.1% within the 17 to 19 GHz band. The proposed double‐layer TMS saved costs, reduced weight and without assembly error is a good candidate for OAM generator.     

Improved Input and State Estimation for Linear Stochastic Systems with Direct Feedthrough

This paper is concerned with the problem of joint input and state estimation for linear stochastic systems with direct feedthrough. Based on the fact that each unknown input between any two time steps is always bounded, a novel improved algorithm is proposed. Compared with existing results, this algorithm can effectively enhance estimation accuracy. Moreover, the stability of the algorithm is also discussed. Finally, an illustrative example is given to demonstrate the effectiveness of the proposed approach.     

Flame Retardancy and Mechanical Properties of Bio‐Based Furan Epoxy Resins with High Crosslink Density

This work outlines an interesting approach to bioepoxy resins from sustainable 2,5‐bis((oxiran‐2‐ylmethoxy)methyl)furan (BOF). The 3,3′‐diamino diphenyl‐sulfone (33DDS) and 4,4′‐diamino diphenyl‐sulfone (44DDS) are employed as hardeners. For comparison, petro‐based networks from diglycidyl ether of bisphenol A (DGEBA) are developed as well. The systematic analyses suggest that the BOF/DDS networks show higher crosslink densities and mechanical properties than DGEBA/DDS thermosets. Remarkably, an attractive multilayer tubular microstructure is fabricated in the BOF/44DDS thermosets, and it greatly enhances the mechanical performance. Apart from that, BOF/DDS composites exhibit excellent flame retardancy. Especially, for BOF/44DDS, the self‐extinguishment happens in 7 s. The fire retardant mechanism confirms that a low heat release rate and heat release capacity as well as a compact char layer occur in the pyrolysis of BOF/DDS. Thus, the BOF/DDS exhibits superior performance over its DGEBA counterparts and meets a wide variety of requirements in engineering.     

Mechanistic Insights and Photodegradation of Heterostructure Graphene Oxide/Titanium Dioxide

Topics in Catalysis - In this study, the electrospinning method was used to prepare graphene oxide/titanium dioxide (GO/TiO2) nanofibers with different contents of GO as photocatalysts used to...     

Modelling of electron energy absorption and backscattering during EBW

A three-dimensional heat flux model for deep-penetrating electron beam welding (EBW) is established to mathematically describe the physical heat generation process during interaction between electrons and the dynamic molten pool free surface. Monte Carlo method is used to determine the electron-target interaction, and random distribution of initial electrons, progressive trajectory tracing and electron backscattering models are used to describe the spatial distribution of electrons absorption. The model is verified in preset keyholes and applied in the simulation on electron beam welding process, and the calculated bead shape shows a good consistency with experimental results.